PREVENTIVO
PREVENTIVO

FAQs

Most common questions on Afontermo, il Nanocappotto.
Only at Afon Casa

AFONTERMO IL NANOCAPPOTTO® is a thermal skim coating with heat-reflecting properties.
Yes, AFONTERMO IL NANOCAPPOTTO® replaces the traditional thermal coat in a few millimetres; it is a highly heat-reflecting skim coating, a feature that determines its high degree of thermal insulation.
We mean a thermal coating with a thin thickness capable of replacing the bulky traditional thermal coat.
AFONTERMO THE NANOCAPPOTTO® in a few millimeters replaces the traditional thermal coat; it is a highly heat-reflective skim coat, a characteristic that determines its high degree of thermal insulation.
Reflectance is the ratio between the quantity of the thermal wave reflected by a body, and the quantity of incident thermal wave. The amount of non-reflected heat wave is absorbed as a 1-R value.
In general, due to the principle of energy conservation, a material partly reflects, partly absorbs, partly transmits. A traditional opaque material has a prevalence in absorbing heat, due to a high emissivity (epsilon 0.85-0.9), approximately equal to that of a black body. A reflective material, on the other hand, tends to absorb an amount equal to 1-R due to a low-emissivity behavior, therefore its contribution to thermal insulation is considerably higher. This is the reason why 4-6 mm (0,16-0,24 in) of AFONTERMO® can replace 13-14 cm (0,51-0,55 in) of traditional thermal coating.
Emissivity is the ability of a body to radiate heat through an empty place at a given temperature, compared to that of a black body at the same temperature. In thermophysics, according to Kirchoff’s law, emissivity is compared to the material’s absorption capacity: if a material absorbs little, it will also emit less infrared radiation. A reflective material absorbs only a minimal part of the thermal wave, therefore it has a low emission behavior.
A low-emissivity material emits reduced infrared radiation, it’s a synonymous of high thermal inertia, i.e. if thermally stressed it does not increase its temperature, because the latter is mainly rejected by the material itself.
No, it is better to use AFONTERMO IL NANOCAPPOTTO® on the intrados of the horizontal opaque element.

AFONTERMO® has to be applied with an American trowel in two coats, waiting at least 48 hours between one coat and the other. Only after the first one is completely dry, then you can apply the second one. More information are available on the product’s technical paper.

Watch the product application video

AFONTERMO® should not be applied to washable paints. It can only be applied after the removal of the pre-existing paint and the application of our Fixative.
AFONTERMO®, with its extraordinary thermal character, prevents the generation of condensation and the consequent molds, it insulates beams and pillars, canceling the effect of thermal bridges. With a few millimeters of AFONTERMO you can replace the bulk of a traditional thermal coating. Furthermore, AFONTERMO® is characterized by a high reflectance (R=80%) which favors the maintenance of ambient temperature and therefore energy saving.
On walls subject to mold and condensation, to thermally insulate new or existing buildings (suitable for energy requalification interventions); instead of a traditional thermal coating, both indoors and outdoors.
AFONTERMO® can be applied to any kind of material support: wood, glass, iron, ceramic, etc.; it can be applied both to the internal and external walls of the house, on beams and pillars.
Only PITTURA (paint) THERMOFOTOCATALITICA AFON CASA from the same line should be used on AFONTERMO®
AFONTERMO® should not be applied on wet or damp walls. In case of walls affected by humidity, NOVOMUR®, the dehumidifying plaster, should then be used.
Yes, AFONTERMO® allows you to definitively eradicate the problem of thermal bridges, eliminating the creation of condensation and mold.

Afon Casa proposes the use of its products to solve moisture and thermal-acoustic insulation problems, in compliance with current regulations and biocompatibility standards.

Products

Discover more

Contact

AFON CASA srl – P.IVA 01842170506 – REA  PI-159492 – Via Emilia Romagna 1 – Gello di Pontedera (PI) 56025

 website by SM WEB DESIGN